Root file close

Sign up using Email and Password. Post as a guest Name. Email Required, but never shown. The Overflow Blog. Stack Gives Back Safety in numbers: crowdsourcing data on nefarious IP addresses. Featured on Meta. New post summary designs on greatest hits now, everywhere else eventually. Related Hot Network Questions.

TApplication creates a ROOT application environment that provides an interface to the windowing system event loops and event handlers. To run the canvas as a standalone application you must create a TApplication object. Calling the Run method starts the event loop. Save the code in a file, for example as demo2. But Thank you for warning me Show 3 more comments. Active Oldest Votes. For the sake of closing this question, here is the answer: Call root.

Improve this answer. Jonah Fleming Jonah Fleming 1, 3 3 gold badges 18 18 silver badges 30 30 bronze badges. Just wanted to add that for me, on OSX and python2, calling root.

God bless you. I was doing this since hours — ajinzrathod. Add a comment. Sign up or log in Sign up using Google. Sign up using Facebook. The following example configures Filebeat to ignore all the files that have a gz extension:. If this option is enabled, Filebeat ignores any files that were modified before the specified timespan.

For example, if you want to start Filebeat, but only want to send the newest files and files from last week, you can configure this option. You can use time strings like 2h 2 hours and 5m 5 minutes. The default is 0, which disables the setting. Commenting out the config has the same effect as setting it to 0.

For files which were never seen before, the offset state is set to the end of the file. If a state already exist, the offset is not changed. In case a file is updated again later, reading continues at the set offset position. Before a file can be ignored by Filebeat, the file must be closed. Then, after that, the file will be ignored. Closing the harvester means closing the file handler. When this option is enabled, Filebeat closes the file handle if a file has not been harvested for the specified duration.

The counter for the defined period starts when the last log line was read by the harvester. It is not based on the modification time of the file. If there are log files with very different update rates, you can use multiple configurations with different values. However this has the side effect that new log lines are not sent in near real time if the harvester is closed. The timestamp for closing a file does not depend on the modification time of the file.

Instead, Filebeat uses an internal timestamp that reflects when the file was last harvested. When this option is enabled, Filebeat closes the file handler when a file is renamed. This happens, for example, when rotating files. By default, the harvester stays open and keeps reading the file because the file handler does not depend on the file name. Filebeat will not finish reading the file.

It does not make sense to enable the option, as Filebeat cannot detect renames using path names as unique identifiers. When this option is enabled, Filebeat closes the harvester when a file is removed. If this setting results in files that are not completely read because they are removed from disk too early, disable this option. This option is enabled by default. When this option is enabled, Filebeat closes a file as soon as the end of a file is reached. This is useful when your files are only written once and not updated from time to time.

For example, this happens when you are writing every single log event to a new file. This option is disabled by default. Only use this option if you understand that data loss is a potential side effect. Another side effect is that multiline events might not be completely sent before the timeout expires. When this option is enabled, Filebeat gives every harvester a predefined lifetime. This option can be useful for older log files when you want to spend only a predefined amount of time on the files.

This option is particularly useful in case the output is blocked, which makes Filebeat keep open file handlers even for files that were deleted from the disk. This combination of settings normally leads to data loss, and the complete file is not sent. If the harvester is started again and the file still exists, only the second part of the event will be sent. These settings help to reduce the size of the registry file and can prevent a potential inode reuse issue.

When this option is enabled, Filebeat removes the state of a file after the specified period of inactivity has elapsed. If a file is updated or appears again, the file is read from the beginning. This config option is also useful to prevent Filebeat problems resulting from inode reuse on Linux. For more information, see Inode reuse causes Filebeat to skip lines.

When this option is enabled, Filebeat cleans files from the registry if they cannot be found on disk anymore under the last known name. This means also files which were renamed after the harvester was finished will be removed.