Dsr 45 manual

Page 73 This message is displayed as a caution for 10 seconds after the start of duplication. Note If any warning message not listed in the table is displayed, consult your Sony dealer. Page 75 Dubbing sound Connect the unit and the sound source using a phono jack cable not supplied. Play back the tape inserted in this unit. Except for clock setting, you can use all other factory-set default parameters but change them as needed. Press the EXEC button to return to the submenu.

OFF : Does not output the time code. ON: Outputs the time code. You can enter up to 10 characters on a tape label. If you select this item, one of the following symbols appears. If no cassette is loaded, nothing is displayed. OFF : Does not display the data codes. DATE: Displays the date when recorded. This is available only when the mode is playback, page 68 GB playback pause, slow playback, cue, or review. This item is only for the DSR Note You can adjust this item only in the externally-synchronized playback mode.

The cassette memory is also duplicated. AUTOq: Starts duplication after rewinding the tape to the beginning in the player and recorder. The cassette memory is not duplicated. The Remote Commander is disabled. Page Troubleshooting Troubleshooting Please check the following before contacting your Sony dealer.

Symptom The power cannot be turned on. The unit will not operate even if the power has been turned on. The cassette cannot be inserted. It takes time to eject the cassette. Page 94 To prevent this incident recurring, do not pull out the plug while adjusting the menu or the brightness of the LCD monitor. Page 95 Symptom The edit timing with the DV connection is not accurate. Playback pause mode is released and the unit goes into the stop mode. Playback pause mode is released and the tape forwards by one frame for each preset time interval.

The unit does not function as part of a digital non-linear editing system. Check them with the following list. Do not use the unit in an extremely hot place If the unit is left in a car parked with the windows closed especially in summer , its cabinet, mechanical parts, etc. After prolonged use, the video heads may become worn out. Page Digital Hours Meter These counts can be displayed on the menu. Use them as guidelines for scheduling maintenance. In general, consult your Sony dealer about necessary periodic maintenance checks.

Track Check Curl Check and Adjustment Rising Check Adjusting Remote Commander Used Adjustment Remote Commander Data Processing Service Mode Emergence Memory Address MSW Code Bit Value Discriminatiion Recorde of Use Check LED Check Switch Check Preparations Before Adjustment Equipment Used Connection of Equipment Checking the Input Signals Adjustment Tapes System Control System Adjustments Input of C Page Initial Data Input of D Page Initial Data Input of E Page Initial Data C Page Table D Page Table E Page Table Node Unique ID No.

Servo and RF System Adjustments Video System Adjustments JC Board Adjustment Back-up duration: up to two weeks. BNC type, 2. Interface Manual for Programmers. Design and specifications are subject to change. Danger of explosion if battery is incorrectly replaced. The AC leakage from any exposed metal part to earth ground. A commercial leakage tester, such as the Simpson or RCA. Follow the manufacturers' instructions to use these.

The Data Precision Measuring the voltage drop across a resistor by means of a. VOM or battery-operated AC voltmeter. The "limit" indica-. Nearly all battery. Using AC voltmeter to check AC leakage. Check the area of your repair for unsoldered or poorly-sol-. Check the entire board surface for solder.

Check the interboard wiring to ensure that no wires are. Look for unauthorized replacement parts, particularly transis-. Point them. Look for parts which, though functioning, show obvious signs. Point them out to the customer and recom-. Recommend the. Refer to page Check and adjustment 1. Play back the tracking tape J-6 and check the states at the en- Connect all the connectors.

There In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Emergence Memory Address Codes corresponding to the errors which occur are written in ad- dresses 38, 3C, 3E.

The type of error indicated by the code are Page C Address 38 to 43 shown in the following table. Bit Value Discrimination Display on the Bit values Bit values must be discriminated using the display data of the ad- adjustment bit3 bit2 bit1 bit0 justment remote commander for the following items. The Y and chroma signals used in the adjustment are shown in Fig.

Input of E Page Initial Data Page Node Unique Id No. D Page Table 8. Decoder free run adj. Node Unique ID No. Input Input of Serial No. General Adjustment 2. Playback Blanking Level Adjustment with 7.

Playback Y Signal Level Adjustment with 7. Page Color Level Adjustment With 7. Color Level Adjustment with 7. Therefore, do not touch the back Signal Arbitrary light holder to avoid electrical shock. Contrast Adjustment PD Board 5.

Playing Level Check 3. Page Front Panel Assembly Ref. Part No. Description Ref. Page Main Frame Assembly Ref. CHIP 4. CHIP 6. CHIP uF 6. CHIP 47uF 6.